DataCard LM200 Guia do Utilizador Página 58
- Página / 109
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
52 SR200 & SR300 Printer and LM200 & LM300 Laminator User Guide
Download To prepare the printer for a firmware download, press the
Enter key. The firmware must be downloaded from a USB-
connected PC with the driver and Status Monitor installed.
See
“Others tab” on page 40 for the Status Monitor page.
DO NOT power off the printer while the firmware is being
downloaded.
Transport Mode OK? Set the Transport Mode when moving or shipping the printer.
Press the Return key to use the transport mode. “Please,
power off” is displayed on the LCD panel. The transport mode
is cancelled when the printer is powered back on.
See
“Preparing the printer and laminator for transport” on
page 66 for information on preparing the printer for
transporting it.
Media Ink Type
YMCK
YMCK-PO
YMCKK
YMCK-UV
Displays the types of ink ribbon and retransfer film that are
loaded in the printer. Press the Next key to scroll to the next
media type.
Datacard supports YMCK, YMCKK and YMCK-PO ink ribbons.
(The printer detects the type of ink ribbon; it cannot be set.)
See your dealer regarding support for YMCKUV ink ribbon.
Film Type
1000
Datacard retransfer film is available in 1000 frames per roll.
Card Thickness
Standard
Thin
Displays the thickness set using the Status Monitor. Standard
for 0.030 inch (0.76mm) thick cards or Thin for 0.010 inch
(0.25mm) thick cards. Set the Card Hopper for this thickness
also; see “Adjust Card Thickness” on page 9.
Contact your dealer or service provider before using 0.010in
(.0.25mm) thick cards.
Print YMC Level Displays the value set using the Status Monitor.
Black level Displays the value set using the Status Monitor.
Black mode Displays the value set using the Status Monitor.
UV Level Displays the value set using the Status Monitor.
PO Level Displays the value set using the Status Monitor.
Retransfer Temp Level Displays the value set using the Status Monitor.
Speed (front) Displays the value set using the Status Monitor.
Speed Front (UV) Displays the value set using the Status Monitor.
Speed (back) Displays the value set using the Status Monitor.
Speed (B-UV) Displays the value set using the Status Monitor.
MG Peel Mode Displays the value set using the Status Monitor.
Menu Display Settings Function
- User Guide 1
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- 5 Messages 5
- Liability statement 6
- Introduction 7
- About the printer 8
- The inside of the printer 9
- The back of the printer 10
- About the laminator 11
- Using the printer 13
- Load Supplies 14
- Remove Hopper and Cards 15
- Replace the Hopper 15
- Adjust Card Thickness 15
- Load ink ribbon 16
- Load retransfer film 17
- Load top side laminate film 18
- Take-up Spool 19
- Supply Roll 19
- Guide Shaft 19
- Metal Guides 19
- Power on 20
- Optional laminator connection 21
- Power on the laminator 21
- Power on the printer 22
- Prepare to print cards 23
- Printing cards 23
- Print cards using ID software 24
- Print from a PC application 24
- Tips for Success 25
- Viewing and changing 27
- Printing Preferences 28
- Print tab 29
- Priority of Data 31
- 1 Panel Auto 2 Panels 31
- Page Split 32
- Security Erase 33
- Printing Area Settings 34
- Printer Settings 34
- Encode tab 35
- Laminate tab 35
- Configuration tab 35
- Printing Properties 36
- Status Monitor 37
- Close the Status Monitor 38
- Printer Status tab 39
- Printer Setting tab 40
- Retransfer tab 41
- Bend Remedy tab 42
- Media Setting tab 42
- Property tab 43
- Laminator tab 44
- Printer Select tab 45
- Others tab 46
- Security Lock tab 46
- Status monitor messages 47
- “Mending 49
- Using the LCD Menus 55
- Using the Printer LCD Panel 57
- Printer Security Number 63
- Red Status Light 64
- Blue Status Light 64
- Operator Button 64
- “Laminator 65
- LCD messages” on page 84 65
- Laminator Settings 66
- Taking care of your printer 67
- Cleaning the printer 68
- Tips – Cleaning card feed 69
- Cleaning the magnetic head 70
- Cleaning the thermal head 71
- Cleaning printer fan filters 71
- Cleaning the laminator 73
- Laminator fan filter 75
- Messages 77
- Printer error recovery 78
- Transfer jam 79
- Turnover jam 80
- Retransfer section jam 81
- Printer LCD messages 83
- “Operating environment” on 85
- “Load cards” on 85
- Take -up side 86
- Laminate pressure motor 86
- Supply side 86
- Supp ly Roll 87
- Patch Position 88
- Card warping 89
- Laminator LCD messages 90
- Supplies 93
- Ink ribbon 94
- Retransfer film 94
- Laminator material 95
- Cleaning supplies 96
- Site requirements 97
- Site guidelines 98
- Ventilation clearance 99
- Printer specifications 100
- Laminator specifications 101
- Magnetic Stripe Encoding 103
- Inline Encoding 104
- Character Code Table 105
- Compliance (FCC) 107
- Regulatory compliance 108
- 11111 Bren Road West 109
- Minnetonka, MN 55343-9015 109
- 952.933.1223 109
- 952.933.7971 FAX 109
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais