DataCard LM200 Guia do Utilizador Página 61
- Página / 109
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SR200 & SR300 Printer and LM200 & LM300 Laminator User Guide 55
HR-T Temp
90 degC to 180 degC
Displays the set point temperature of the top heat roller. (The
temperature may be 185 degC or higher depending on the
firmware version of the card printer.)
HR-B Temp
90 degC to 180 degC
Displays the set point temperature of the bottom heat roller.
(The temperature may be 185 degC or higher depending on
the firmware version of the card printer.)
Speed
3.0 mm/s to 12.0 mm/s
Displays the card speed during lamination.
Cooling Time
0sec, 5sec, 7sec, 10sec,
15sec, 20sec, 30sec
Displays the standby time for cooling down the card before
lamination starts.
HR Control
Off
On
Displays whether the laminator will enter low temperature
standby mode. This setting works simultaneously with the
card printer setting. This is always set to ‘On’ automatically
when overlay film is selected. (Regardless of the setting, the
laminator should be put into standby if you will not be printing
cards for a long time.)
Count Displays the number of laminations performed after the last
roller cleaning. This number is reset to 0 each time a roller
cleaning is performed.
Network
Printer Name
PRINTER01 to
PRINTER09
Assign the Network Name of the printer. Change this name
when more than one SR200 or SR300 printer is connected to
the network. Choose from the names supplied. If you set up a
network printer on the PC using a USB connection, this name
can be assigned from the PC.
Host IF
USB
LAN
View the connection method for the printer and PC, either
USB or LAN (Ethernet). The setting defaults to USB when the
printer is connected to a PC using a USB cable.
Network>IPv4 DHCP
ON
OFF
Dynamic Host Configuration Protocol (DHCP) is a network
feature that assigns IP addresses to devices on the network.
• ON uses DHCP to assign the printer IP address. The IP
Address can change when you power off the printer and
then power it on again.
• OFF means that you must assign the IP Address of the
printer and it will not change (Static IP). Use this setting if
your network does not support DHCP.
Ask your network administrator which setting to use.
Setting:
IP Address
The default IP address of the printer is 192.168.0.141, and is
displayed when the printer is powered on for the first time or
when DHCP is set to On.
If you do not use DHCP, ask your network administrator for
the IP Address to use.
Menu Display Settings Function
- User Guide 1
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- 5 Messages 5
- Liability statement 6
- Introduction 7
- About the printer 8
- The inside of the printer 9
- The back of the printer 10
- About the laminator 11
- Using the printer 13
- Load Supplies 14
- Remove Hopper and Cards 15
- Replace the Hopper 15
- Adjust Card Thickness 15
- Load ink ribbon 16
- Load retransfer film 17
- Load top side laminate film 18
- Take-up Spool 19
- Supply Roll 19
- Guide Shaft 19
- Metal Guides 19
- Power on 20
- Optional laminator connection 21
- Power on the laminator 21
- Power on the printer 22
- Prepare to print cards 23
- Printing cards 23
- Print cards using ID software 24
- Print from a PC application 24
- Tips for Success 25
- Viewing and changing 27
- Printing Preferences 28
- Print tab 29
- Priority of Data 31
- 1 Panel Auto 2 Panels 31
- Page Split 32
- Security Erase 33
- Printing Area Settings 34
- Printer Settings 34
- Encode tab 35
- Laminate tab 35
- Configuration tab 35
- Printing Properties 36
- Status Monitor 37
- Close the Status Monitor 38
- Printer Status tab 39
- Printer Setting tab 40
- Retransfer tab 41
- Bend Remedy tab 42
- Media Setting tab 42
- Property tab 43
- Laminator tab 44
- Printer Select tab 45
- Others tab 46
- Security Lock tab 46
- Status monitor messages 47
- “Mending 49
- Using the LCD Menus 55
- Using the Printer LCD Panel 57
- Printer Security Number 63
- Red Status Light 64
- Blue Status Light 64
- Operator Button 64
- “Laminator 65
- LCD messages” on page 84 65
- Laminator Settings 66
- Taking care of your printer 67
- Cleaning the printer 68
- Tips – Cleaning card feed 69
- Cleaning the magnetic head 70
- Cleaning the thermal head 71
- Cleaning printer fan filters 71
- Cleaning the laminator 73
- Laminator fan filter 75
- Messages 77
- Printer error recovery 78
- Transfer jam 79
- Turnover jam 80
- Retransfer section jam 81
- Printer LCD messages 83
- “Operating environment” on 85
- “Load cards” on 85
- Take -up side 86
- Laminate pressure motor 86
- Supply side 86
- Supp ly Roll 87
- Patch Position 88
- Card warping 89
- Laminator LCD messages 90
- Supplies 93
- Ink ribbon 94
- Retransfer film 94
- Laminator material 95
- Cleaning supplies 96
- Site requirements 97
- Site guidelines 98
- Ventilation clearance 99
- Printer specifications 100
- Laminator specifications 101
- Magnetic Stripe Encoding 103
- Inline Encoding 104
- Character Code Table 105
- Compliance (FCC) 107
- Regulatory compliance 108
- 11111 Bren Road West 109
- Minnetonka, MN 55343-9015 109
- 952.933.1223 109
- 952.933.7971 FAX 109
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais